Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Trusted Duct Repair & Sealing for Bellevue Homeowners
Leaky ducts waste the air you’re paying to cool, and in Bellevue’s older ranch homes and split-levels the damage usually hides in the crawlspace or attic where nobody sees it. That means higher bills, dustier rooms, and a system that runs longer than it should. Our technicians have up to 11 years of experience finding those leaks with professional-grade equipment, and duct repair and sealing is handled in-house, so we fix what we find on the same visit instead of sending you off to find another contractor. Call (877) 560-9584 for a free estimate.
We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
What Our Duct Repair & Sealing Service Includes
Every duct system we open gets a real inspection before we quote anything. Here’s what the work looks like across the six things we do most.
Duct Sealing
Duct sealing closes the gaps at joints, seams, and connections that bleed conditioned air into spaces you don’t live in. It’s what you need when rooms near the thermostat feel fine and rooms at the ends of the runs don’t, or when your energy bill climbs without an obvious cause. We seal the accessible system with the right method for each section rather than painting a single coat over everything.

Flex Duct Repair
Flexible duct is common in Bellevue attics and additions, and it fails in predictable ways: crushed runs, torn outer jackets, and sagging loops that choke airflow. It needs repair when a run is kinked or a section has been stepped on or pulled loose. We cut out the damaged section and re-support the run properly so it doesn’t collapse again.

Metal Duct Repair
Sheet metal trunks and branches develop separated seams, popped joints, and rusted sections over time. You’ll notice it as rattling, whistling, or a room that never gets enough air. We resecure and seal metal runs and replace badly deteriorated sections so the trunk line holds pressure like it should.

Duct Insulation
Insulation on ductwork keeps the air at the temperature it left the air handler with. Bare or disintegrating insulation in a hot Bellevue attic means cold air arrives warm at the register. We restore insulation where it has broken down, especially on runs that cross unconditioned space.
Mastic Sealant
Mastic is a heavy brush-on sealant that stays flexible and lasts far longer than standard duct tape, which fails in attic heat. It’s the right choice for metal joints and plenum connections that need a permanent seal. We apply it to the seams we can reach, then check the seal before the system is closed back up.
Air Leak Repair
Air leak repair is the diagnostic side: finding where the system is losing air before anything gets sealed. Leaks hide at the plenum, at register boots, and at connections buried above ceilings. We locate them with pressure checks and airflow readings, then repair the ones that matter most for your bill and comfort. If you want the full picture of how cleaning and sealing work together, see our air duct cleaning in Bellevue page.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Brands We Service for Duct Repair & Sealing
We work with Rotobrush and Nikro systems, which are the professional-grade tools commercial contractors and restoration specialists rely on. That familiarity carries over to the ductwork itself, including the components those systems connect to. If your home has an Aprilaire or Honeywell whole-home air quality setup, we know where that equipment ties into the return and how to check it during the same visit rather than working around it.
We also use Abatement Technologies HEPA and negative-air equipment when a repair job is dusty enough to need containment. That’s remediation-grade gear, and it keeps particulate out of your living space while we’re opening a system. Whether you have rotating brush equipment from Rotobrush, a Nikro setup, or any other make, we can help.
Signs You Need Duct Repair & Sealing Right Now
- Rooms that never match the thermostat. If one bedroom runs warm while the hallway feels fine, the branch feeding it is likely leaking or restricted. Sealing the run often fixes the imbalance without touching the thermostat.
- Energy bills climbing with no other explanation. Leaky ducts push the system to run longer to reach the same temperature. A pressure check will tell you whether the money is leaving through the ductwork.
- Dust settling on surfaces right after you clean. Gaps in return ductwork pull attic or crawlspace air into the system and blow it into rooms. That’s a repair problem, not a dusting problem.
- Whistling, rattling, or popping at the registers. Noise at a vent usually means a loose connection or a collapsed flex run nearby. Left alone, it can grow into a full run replacement.
- Visible tears, crushed runs, or disconnected joints. If you’ve seen any of this in the attic or crawlspace, the system is losing air right now. Call (877) 560-9584 and we’ll assess it.
Our Duct Repair & Sealing Process – Step by Step
- 1
Full system inspection. We open the accessible ductwork, photograph what we find, and check the air handler, plenum, and register boots. You see the same pictures we do before anyone quotes a repair.
- 2
Pressure and airflow testing. We measure static pressure and airflow to locate where the system is losing air, not just where it’s easy to see. This tells us which repairs actually move the needle on your bill.
- 3
Written estimate, one flat price per system. You get a written estimate with the scope of work before anything starts. The final price is set by that written estimate, and it doesn’t grow once the technician is on site.
- 4
Contained repair and sealing. We seal, repair, and reinsulate with Abatement Technologies HEPA filtration running where needed to keep dust out of your rooms. Flex and metal runs get repaired with the method that fits each section.
- 5
Post-repair verification and photos. We retest and hand you before-and-after photos of your own ductwork. If a problem is beyond sealing and needs a section replaced, we handle it in the same visit. You can read more about our duct repair & sealing approach here.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Duct Repair & Sealing Cost in Bellevue?
Duct repair and sealing in Bellevue typically runs $350 to $1,800 for a residential system, with most single-area sealing jobs landing between $350 and $650 and larger whole-system repairs climbing from there. The final number depends on how much ductwork needs work, which material it’s made of, and how hard it is to reach.
| Service | Typical Bellevue range |
|---|---|
| Air leak repair (targeted) | $250 – $550 |
| Mastic sealant on accessible joints | $300 – $700 |
| Flex duct repair (per run) | $180 – $400 |
| Metal duct repair or section replacement | $300 – $900 |
| Duct insulation restoration | $350 – $1,200 |
| Whole-system sealing | $800 – $1,800 |
What affects the price most is access. A run you can reach from a walk-in attic takes far less time than one chased through a finished ceiling. Material matters too: metal repairs involve cutting and fitting, while flex runs are usually faster. The way to avoid overpaying is to get the whole picture up front, which is why our estimate is free and written before any work begins.
The written estimate sets the final price. It covers the inspection, the test readings, the repair scope, and the before-and-after photos. If you also want the system cleaned while we’re in it, ask about duct repair & sealing combined with a full cleaning visit for neighboring homes.
Duct Repair & Sealing Near Bellevue – Our Service Area
We serve Bellevue and the surrounding middle Tennessee communities, including West Meade, Sylvan Park, The Nations, Belle Meade, Kingston Springs, Pegram, Forest Hills, Green Hills, Oak Hill, Fairview, and Ashland City. Response times depend on the day and the route, but our crews dispatch from 7am to 7pm, Sunday through Friday, and the phone is always answered. Homes out toward Kingston Springs and Pegram sometimes need a little more lead time on scheduling. Learn more about our duct repair & sealing availability for nearby neighborhoods.
Serving Bellevue, TN – Our Local Coverage Area
We serve Bellevue and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Duct Repair & Sealing in Bellevue
Duct repair and sealing is fixing the physical damage to ductwork and closing the gaps that let conditioned air escape before it reaches your rooms. Repair covers crushed flex runs, separated metal joints, and torn insulation. Sealing closes the leaks at seams, plenum connections, and register boots. Together they restore the system’s ability to move air where you need it. Call (877) 560-9584 for a free estimate.
Most residential jobs take a few hours to a full day, depending on how many runs need work and how accessible they are. Targeted leak repair on a handful of joints can wrap up in a half day. Whole-system sealing with insulation restoration usually takes a full visit. We’ll tell you up front so you can plan around it.
Typical costs run $350 to $1,800 for a residential system, with most single-area jobs between $350 and $650. Whole-system sealing with insulation work sits at the upper end of the range. The written estimate sets the final price before we start. Call (877) 560-9584 for an exact quote; estimates are free.
Low quotes usually cover only what’s visible from the register, not the actual leaks in the attic or crawlspace. Some skip pressure testing entirely, so nobody knows whether the repair worked. We test before and after and show you photos of your own ductwork. A flat price per system with the scope in writing is what keeps the final bill honest.
Yes. We run Rotobrush and Nikro systems on a routine basis, and we also use Abatement Technologies HEPA and negative-air equipment for containment. We also work with Aprilaire and Honeywell whole-home air quality systems, so if your ductwork connects to one of those, we can check it in the same visit. Whether you have Rotobrush, Nikro, or any other make, we can help.
Same-day service is available when the schedule allows, and our crews dispatch from 7am to 7pm, Sunday through Friday. We answer 24/7, and a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. We’re closed on Saturday. Call (877) 560-9584 to get on the schedule.
Clear access to the attic hatch or crawlspace entry and move anything blocking the registers. Secure pets in a room away from the work area. If you have questions about your Aprilaire or Honeywell equipment, mention it when you book so we bring the right gear. That’s all most homes need. Call (877) 560-9584 for a free estimate.
Schedule Your Duct Repair & Sealing Service in Bellevue Today
Leaky ductwork doesn’t fix itself, and every month it runs costs you on the energy bill. Call (877) 560-9584 to book a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You’ll get a flat price per system agreed before work starts, before-and-after photos of your own ducts, and a satisfaction guarantee. No obligation, no pressure.
Written by the team at Air Duct Cleaning Bellevue.